جستجوی کد خطای ولوو و رنو تراکس

The signal voltage at the ECS unit contact from the pressure sensor exceeds 4.5 V. The signal wire is shorted to the power supply wire. The ground wire is broken. The pressure sensor may be faulty.

The signal voltage at the ECS unit contact from the pressure sensor is less than 0.5 V. The signal wire is shorted to ground. The signal wire or sensor power wire is broken. A faulty pressure sensor is likely present.

Freezing of water or partial contamination in the lines or other air suspension components. A short circuit in the signal wire to the power supply or a break in the ground wire.

The sensor ground wire is broken. The signal wire is shorted to the power wire. The sensor is likely faulty.

The signal voltage at the ECS unit contact from the pressure sensor exceeds 4.5 V. The signal wire is shorted to the power supply wire. The ground wire is broken. The pressure sensor may be faulty.

The signal voltage at the ECS unit contact from the pressure sensor is less than 0.5 V. The signal wire is shorted to ground. The signal wire or sensor power wire is broken. A faulty pressure sensor is likely present.

Freezing of water or partial contamination in the lines or other air suspension components. A short circuit in the signal wire to the power supply or a break in the ground wire.

The sensor ground wire is broken. The signal wire is shorted to the power wire. The sensor is likely faulty.

The signal voltage at the ECS unit contact from the pressure sensor exceeds 4.5 V. The signal wire is shorted to the power supply wire. The ground wire is broken. The pressure sensor may be faulty.

The signal voltage at the ECS unit contact from the pressure sensor is less than 0.5 V. The signal wire is shorted to ground. The signal wire or sensor power wire is broken. A faulty pressure sensor is likely present.

Freezing of water or partial contamination in the lines or other air suspension components. A short circuit in the signal wire to the power supply or a break in the ground wire.

The sensor ground wire is broken. The signal wire is shorted to the power wire. The sensor is likely faulty.

The signal voltage at the ECS unit contact from the pressure sensor exceeds 4.5 V. The signal wire is shorted to the power supply wire. The ground wire is broken. The pressure sensor may be faulty.

The signal voltage at the ECS unit contact from the pressure sensor is less than 0.5 V. The signal wire is shorted to ground. The signal wire or sensor power wire is broken. A faulty pressure sensor is likely present.

Freezing of water or partial contamination in the lines or other air suspension components. A short circuit in the signal wire to the power supply or a break in the ground wire.

The sensor ground wire is broken. The signal wire is shorted to the power wire. The sensor is likely faulty.

The signal voltage at the ECS unit contact from the pressure sensor exceeds 4.5 V. The signal wire is shorted to the power supply wire. The ground wire is broken. The pressure sensor may be faulty.

The signal voltage at the ECS unit contact from the pressure sensor is less than 0.5 V. The signal wire is shorted to ground. The signal wire or sensor power wire is broken. A faulty pressure sensor is likely present.

Freezing of water or partial contamination in the lines or other air suspension components. A short circuit in the signal wire to the power supply or a break in the ground wire.

The ECS unit detects that one of the switches on the air suspension control panel is in two positions simultaneously. There is a short to ground in the wires between the control panel and the ECS unit. The air suspension control panel may be faulty.

Mechanical failure of the relay.

There is a fault in the wiring or in the data link connectors between the ECS unit and other control units.

Programming error or internal malfunction of the air suspension control unit. Reprogram the control unit. If the error code reoccurs, replace the control unit.

There's a fault in the wiring or data link connectors between the ECS unit and other control units. The control unit is likely faulty.

Parameters are programmed incorrectly. Check that the parameters are set correctly. Reprogram the ECS unit.