جستجوی کد خطای ولوو و رنو تراکس

The dehumidifier control unit's internal memory is faulty, or the parameters are incorrectly programmed. Try resetting the MID185 and reprogramming it. If the problem persists, replace the dehumidifier.

The parameters in the dehumidifier control unit are incorrectly programmed. Try resetting the MID185 and reprogramming it. If the problem persists, replace the dehumidifier.

The parameters in the dehumidifier control unit are incorrectly programmed. Try resetting the MID185. Reprogram it. If the problem persists, replace the dehumidifier.

The dehumidifier control unit is faulty. Replace the dehumidifier.

The dehumidifier control unit is faulty. Replace the dehumidifier.

The signal from the brake system control unit (MID136) is incorrect or absent. The SAE J1587/J1708 data link wiring is broken or partially damaged. The connector contacts are damaged or corroded. The brake system control unit (MID136) or the vehicle control unit (MID144) may be faulty.

High voltage between power pin 3 and ground pin 4 on the air dryer connector. The alternator may be faulty. Try resetting the MID185.

Low voltage between power contacts 3 or 1 and ground contact 4 on the air dryer connector. Possibly a short to ground in the power wires. Try resetting the MID185.

There is an open circuit in the power wires to air dryer contacts 3 or 1, and an open circuit in the ground wire to air dryer contact 4. One of the fuses, F8 or F47, has blown. Try resetting the MID185.

The control unit is in self-test mode. Try restarting the MID185.

Incorrect checksum value at startup. Parameters in the dehumidifier control unit are incorrectly programmed. Try resetting the MID185. Reprogram it.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

Incorrect checksum value at startup. Parameters in the dehumidifier control unit are incorrectly programmed. Try resetting the MID185. Reprogram it.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

There's an internal fault in the air dryer control unit. Try resetting the MID185. Reprogram it. If the fault persists, replace the air dryer.

The dehumidifier control unit's internal temperature sensor signal is outside acceptable limits. The dehumidifier control unit is faulty. Replace the dehumidifier.

The unit temperature is below -48°C (-48°F) or above +93°C (203°F). This could be due to extreme weather conditions or a faulty temperature sensor. Restart the MID185 at an ambient temperature of 20°C (68°F). If the code remains active, replace the air cleaner.

The signal coming from the engine control unit (MID128) is incorrect or absent. The data link wiring is broken or partially damaged. The contacts in the connectors are damaged or corroded. The engine control unit may be faulty.

The pressure in the parking brake circuit increases, even with the solenoid valve activated. Air is entering from the trailer circuit or the air dryer is faulty. Try completely draining and filling the pneumatic system. Try resetting the MID185.